Glock 17 Pros And Cons - The Glock 17 has become an icon since it was first developed in the early 1980s. A lot has changed in the last 40 years, but the overall design of the Glock has not been one of them.
If you were to compare an original Glock 17 and a current generation Glock 17 side by side, there would be only subtle hints as to what had changed.
Glock 17 Pros And Cons
Things like the Glock added a dust cover with a rail under the barrel. Glock also added finger grooves to the grip and later removed those grooves in the latest iteration.
Glock 17 9mm [counter Strike: Source] [mods]
Glock went from a very smooth texture to one that will literally wear/tear holes in your parts if you are not careful or careful.
The grip of the Gen 4 Glock 17 is nothing special. Normally when you say those words, it's not good, but here I'd say it really is.
Glock has found what I think is the perfect sweet spot between a smooth piece of polymer and a texture that can peel off layers of skin if you rub your hand over it a little too hard.
As Glocks grew in popularity, people began to rub off the factory texture and then score the polymer frame with a welder, or, more and more popularly, use a laser to engrave a new texture or design of your choice.
Glock 45: Can The G45 Truly Mix The Glock 17 And Glock 19 9mm Guns?
This customization makes for interesting grip textures and it seems the only limit is your imagination and wallet.
Ergos on a Glock are almost non-existent. It's a Glock. Most people feel like picking up a brick.
I find that in the world of handguns their design is unique, and the feel they give me as a shooter is equally unique. If I shoot one of my other pistols and then immediately switch to one of my various Glocks, the feel of the gun in my hand is noticeably different.
As mentioned above, Glock uses the same grip angle on all of their pistols. Although they are different from other brands, the continuity this feature brings to the table brings familiarity when moving from Glock to Glock.
Best Holster For Glock 17
The fact that I have medium sized finger grooves on Glocks and other guns didn't bother me at all, so I could take them or leave them as they are.
The piece is nice and is also found in the finger groove sections at the low points where the finger pads rest.
Glock provides thumb dimples on both sides of the top of the grip. I find this helpful in placing my strong thumb in the socket and helps me align the sight and position the bore.
The Glock folks also provided the end use with a slight cut on the trigger guard. While it in no way compares to a custom job, it does a decent job of letting the shooter's hand come out a little higher in the grip.
The 5 Best Glock 17 Holsters [2021]
While the past few decades have been designed to replace the cheap plastic sights often found on stock Glocks, there is no need to upgrade to a Gen 4 MOS as long as you have an optic installed.
Some would argue that even though you have optics installed you should still have a set of sights on a gun, I think this is a decision made out of preference rather than necessity.
If you choose to install a set of iron sights, there are several different options to choose from.
The list is much narrower than a non-MOS Glock, if you want the sights to be usable with the optic mounted.
Glock 17 Mos Gen4
The list is narrowed down to points of interest of "oppressive height". This is because the installed red dot body, whatever it is, will block the proper sight alignment of normal elevation mirrors.
You will be able to see the rear sight, but you will not be able to align the front and rear sights into a correct mirror image because of the red dot.
Depending on the application and use of the weapon, this may dictate your decision regarding aftermarket sights.
For a gun used on the range to punch through paper, I don't think I would spend the extra money to buy suppressor elevation sights to match my mounted red dot MOS.
Glock 19x (g19x), Glock 19 (g19) Gen5, Glock 17 (g17) Gen5, And Glock 34 (g34) Gen5 At The Range: Some Interesting New Pistols
If the MOS was used for self defense or service, I would highly encourage the purchase and use of iron sights along with the Glock MOS red dot.
This is Glock's (late) answer to the thousands of people who sent their stock slides to a machine shop to have a red dot milled and tapped.
As with most things, Glock seems to be dragging its feet when it comes to advancing its design to match the booming trend of mounting red dots on its pistols.
I remember flipping through the gun magazines at the grocery store almost a decade ago and seeing big, bulky red dots mounted on photo rails mounted in turn on the dust cover.
Elite Force Glock 17 Gen 5 Gas Blow Back Airsoft Pistol ( Black )
These guns looked bulky and unwieldy with the addition of all the hardware to accomplish the task of adding a red dot to the gun.
As technology often does, the hips got smaller and smaller until they were small and light enough that red dots could be mounted on a gun slide and not interfere with the proper operation of the firearm.
The location chosen to be used for the MOS is the typical location for placing modern red dots. The MOS cut is between the tail of the rear sight and the rear of the lock if the barrel hood with the slide.
They have a standard capacity of 17 rounds. You can also get extended magazines that will increase the total round count.
Glock 22 Or Glock 17? Which Do You Prefer
The controls on any gun, especially a pistol, will make or break the gun and the controls on the Glock 17 are tried and true.
This gives the shooter a free attachment point that shouldn't interfere with the normal command grip of the weapon, but is also large enough to act positively.
The magazine catch is reversible, but not quite ambidextrous in the sense that it sits on the left or right side of the gun, depending on the owner's preference and location.
The slide stop is in its traditional position on the left side of the gun directly above the magazine release.
Glock 43 Vs. Glock 26 Comparison
The position of the magazine release and slide stop are such that they can both be operated with the right thumb of most adults.
They can also be operated with the thumb of the support hand if that is more convenient for the shooter.
The trigger comes standard with Glock's safe action that requires the central part to be pulled before the rest of the trigger can be pulled.
It breaks relatively cleanly at around 5 to 5.5 pounds. This is a decent weight and helps ensure that the trigger pull is aimed.
Glock 17 Mos Vs Walther Q5 For Uspsa Carry Optics Division
The trigger face of the G17 MOS is a smooth style. Some prefer this type, while others prefer the square trigger that Glock usually offers on other models.
Replacing the trigger shoe is a relatively simple matter if you want to install something completely different.
What can i say; There isn't much to talk about in terms of styling for any Glock.
However, this MOS gets some style points for having an FDE frame, or a dark ground flat frame instead of the usual black you usually see.
Best Glock For First Time Buyers
The dark, flat ground color used is a bit different than what we've come to expect from companies like Magpul and other manufacturers.
It should be noted that this FDE is actually a colored polymer, and not a spray on cracotta or other glaze that some companies or third party distributors add.
If you want the slide coated to match, you will need to manually select the color based on visual inspection, not just the color name.
Like other pistols that have added red dots, the Glock 17 MOS can be customized to your red dot preferences, giving it a unique style for the shooter/equipment.
Glock 17 P80 Build
We will explore some of the more popular options that people like to incorporate with their defense pistols listed below.
To solve the problem of people sending their slides for grinding, Glock came out with the MOS system. This system allows a person to put a red dot on their Glock if they want, or not if that is their preference. It also allows the end user the modularity to switch to a different optic that has a different mounting footprint simply by connecting the correct MOS mounting plate with the desired optic.
Basically, it lets you play musical chairs with the red dot on the gun where, like before, you once ground the slide for
Shopify pros and cons, acumatica pros and cons, ehr pros and cons, bankruptcy pros and cons, pros and cons list, tableau pros and cons, invisalign pros and cons, lasik pros and cons, refinance pros and cons, xero pros and cons, coolsculpting pros and cons, quickbooks pros and cons
0 Comments